Kuhn 4142 Stationary
Double tap to zoom
THE BOTEC® ADVANTAGE
A Quality Ration and Complete Cleanout
The raised lower right auger configuration, along with the close tolerance between the auger flighting and the auger troughs, results in a fast and complete cleanout. The offset upper right auger in combination with the raised lower auger requires less horsepower and provides a faster mix time.
Mix Full or Partial Loads Due to the cross-mixing action of horizontal auger mixers, Botec TMR mixers can properly mix batches that fill only a portion of the mixing tub providing you with the versatility to mix any size ration.
Even, Consistent Discharge
The close auger tolerances and raised lower auger design provide a fast, consistent discharge from beginning to the end of unloading. This results in even feed placement across the entire length of the bunk without a delay for mixer cleanout.
Splined Auger Shafts
Splined auger shafts allow a strong, reliable torque transfer and provide easier sprocket alignment and maintenance.
Having parallel lower augers creates more force between the augers without increasing mixing capability. Parallel augers also do not transition the feed from right to left as well as if the right auger was raised. This design leads to slow, incomplete cleanout, decreases the mixer's processing ability and increases the horsepower requirements.
SIMPLE, DEPENDABLE DESIGN
Heavy-Duty Rear Drive
The reliable heavy-duty roller chain drive runs in oil and has spring-tensioned poly idlers for long life.
Nylon Auger Bearings
Reliable, externally mounted nylon bearings provide simple maintenance with reduced sensitivity to contamination.
Discharge Door & Linkage
Large door openings allow for better ration flow and faster feed delivery. The discharge door frame is more rigid and less complex for dependable day-in and day-out operation.
4-Point Weigh Bar System
Four-point weigh bar system comes standard as a cost effective and simple weighting system, yet still maintains 99.5% accuracy.
TAILOR YOUR MACHINE
Multiple Discharge Options
To best suit your feeding needs, you can choose from a slide tray, chain and slat conveyor or a 3-auger discharge to be equipped on your 4100 Series mixer.
The side discharge slide tray has simple hydraulic controls and helps guide feed further away from the tire path. Magnets are standard on slide tray.
Chain and Slat Conveyor
Rugged chain and slat conveyor options provide the ultimate in durability and long life. Heavy-duty components ensure reliable service and multiple conveyor length options offer unmatched flexibility to match different feeding situations.
The 3-auger discharge allows adjustment for feeding into higher bunks. It has a simple, hydraulic drive that provides smooth, even discharge. Long lasting, poly chute liners help prevent rust and limit wear. The 3-auger discharge comes standard with fixed tip-off and built-in magnets.
Trailer & Truck Models
To suit your operation’s needs, KUHN 4100 Series mixers are available in a trailer or truck-mounted configuration. Trailer models are the most popular configuration as they are the most economical and versatile. Being detachable allows the tractor to be used elsewhere on the farm when not in use for feeding. Truck-mounted models are a suitable option for those that have to feed cows at several different locations, with large travel distances. This option allows a feeder to quickly get from the mixing location to the feed bunk and back again.
|Capacity||420 ft³ (11.9 m³)|
|Capacity with Extensions||460 ft³ (13 m³)|
|Maximum Net load||12,600 lbs (5,715 kg)|
|Overall Height||97" (246 cm)|
|Overall Height - With Extensions||105" (267 cm)|
|Overall Length||220" (559 cm)|
|Mixing Chamber Length||168'' (427 cm)|
|Overall Width - Mixer Only (No Discharge)||89" (226 cm)|
|Lower Auger Flighting Thickness||1/2'' (1.3 cm)|
|Lower Auger Flighting Diameter||24'' (61 cm)|
|Lower Auger Tube - Outside Diameter||5 9/16'' (14 cm)|
|Lower Auger Drive Shaft Diameter||3'' (7.6 cm)|
|Upper Auger Flighting Diameter||24'' (61 cm)|
|Upper Auger Flighting Thickness||3/8" (1 cm)|
|Upper Auger Tube - Outside Diameter||5 9/16'' (14 cm)|
|Upper Auger Drive Shaft Diameter||3'' (7.6 cm)|
|Lower Auger Tube - Wall Thickness||1/2'' (1.3 cm)|
|Upper Auger Tube - Wall Thickness||1/2'' (1.3 cm)|
|Roller Chain Drive||100-120|
|TUB & TRAILER CONSTRUCTION|
|Unit Weight||12,600 lbs (5,715 kg)|
|Door Opening Size||31.5'' x 32.25'' (80 x 82 cm)|
|Sidewall Thickness||3/16'' (0.5 cm)|
|Auger Hopper Thickness||5/16'' (0.8 cm)|
|Motor Mount to Center of Discharge Door||71" (180 cm)|
|Discharge Height - With Rails and Scales||20" (51 cm)|
|Mounting Base Length||144" (366 cm)|
|Mounting Base Width||44" (112 cm)|
|Electric Motor Horsepower||15 - 20 HP (11 - 15 kW)|
Have A Question?
Contact us, we want to hear from you